TOOLS General Workshop Tools DA1650 DA7288 Automotive Current Tester Automotive Current Tester LCD Display For the rapid safe and accu- This automotive current rate testing of DC current on tester with LCD display, plugs 12v vehicles. The tool plugs directly into the fuse box and straight into the vehicles fuse can be used on mini, standard board and displays the current and maxi fuse connections. on the large LCD display. Blades may get hot during use Specification range 0-48volt and care should be taken for max 20 amps, 12v battery 2 mins whilst they cool down. included. > Fits mini and maxi fuses > Quick and safe > Current range 0-80A > Plugs straight into the > Safe and easy way to check vehicle fuse board automotive current > Large LCD display > LCD display > Specification range > Hold and peak function 0-48volt max 20 amps with bar graph > 12v battery included DA3247 Balance Shaft Removal & Installation Kit Discovery 5 Discovery Sport - 2015 - 2019 Range Rover Evoque - 2015 - 2018 Range Rover Sport - 2016 - 2018 Range Rover Velar - 2017 - Designed to allow the safe removal, fitting and timing of the gear driven balance shaft on the Jaguar Land Rover AJ200 2.0L diesel engines. The kit contains all the DA3248 DA7399 essential components to enable the Long Series Hex Bit 3/8”D 11mm Exhaust Gas Temperature Sensor Socket balance shafts to be aligned when Ideal for injector clamp bolts and caliper Range Rover - 2011 - 2012 reassembling the components. Made in Sheffield. Use in accordance with OEM instructions.bolts. Size: 11mm x 100mm long. SocketRange Rover - 2013 - 2017 Equivalent to OEM - JLR-303-1662 / JLR-303-1663-1 / JLR-303-1663-2 / JLR-303-1663-3 manufactured from Chrome Vanadium. Range Rover Sport - 2014 - 2017 JLR-303-1664 / JLR-303-1665 Bit from S2 Steel. > Required to remove/install the exhaust gas temperature sensor > Equivalent to OEM 303-1573 > 13mm hex x 6mm deep > Socket equipped with a 13mm hex to use with appropriate spanner or wrench > Made in Sheffield. DA3898 NEW Flange Holding Tool Defender - 2020 onwards Discovery 4 / Discovery 5 Freelander 2 Range Rover Velar DA1765 NEW Range Rover Evoque - 2012 - 2018 Hose Clamp Tool - Bar Type Range Rover Sport - 2010 - 2013 140mm long hose clamp tool. Suitable for DA5443 NEW Range Rover Sport - 2014 - 2022 use on rubber hoses, making it ideal for Drain Plug Removal Tool Range Rover Sport - 2023 onwards both brake and fuel lines together with Slotted oil drain plug tool. Range Rover - 2002 - 2009 coolant hoses. Steel construction with round For use with a 19mm spanner or socket. Range Rover - 2013 - 2022 chrome plated bars to help prevent damage. Series, Defender & Range Rover Classic Range Rover - 2022 onwards > Clamps any hose simply and effectively DA3499 Used to hold the flange whilst removing > Chrome plated bars Automatic Gearbox Alignment Tool and replacing the flange nut on JLR 5.0L > Use on brake, fuel and heater hoses Defender / Discovery 1 / Discovery 2 / Range and 3.0L diesel engines. Equivalent to OEM > No sharp edges Rover Classic / Range Rover P38 205-053. > Ensures complete clamp An essential tool for the correct setting and alignment of the XYZ switch (gear selector position and starter inhibitor switch) on the ZF4HP22, ZF4HP24, ZF4HP44 automatic gearboxes. Equivalent to OEM 307-498 & LRT-44-011. Made in Sheffield. DA3524 DA1848 NEW Hub Puller Adaptor Kit Laser Fork Ball Hub puller plate for use on 3, 4 and 5 bolt DA7355 NEW Joint Separator fixing drive flanges. Laser Damaged Hex Bolt Extractor For separating ball joints, this tool > PCD 97 - 123mm 7 piece hex bolt extractor bit set designed to uses the forked wedge principle. > Complete with 5/8”UNF adaptor for slide remove damaged, rounded, or corroded allenDesigned to be used with a hammer hammer (Hex) bolts or screws. Sizes: 1.5, 2, 2.5, 3, 4, separate the joint from the steering arm. Fork > 1½” x 16tpi plate thread allows use of 5 & 6mm x 50mm long. 1/4” shank with quick dimensions: internal 14mm, thickness of shaft hydraulic ram chuck end. Packed in a storage case. For use 22mm, overall length 200mm. Manufactured > Can also be used with an impact force with a drill. to ANSI and DIN standards. screw Photo by Darren Whiley 278